Amana furnace code b9: Low Indoor Airflow
Try DIY first, then call a pro
What does b9 mean on an Amana furnace? Indoor airflow fell below the minimum the control calculates from its shared data. The furnace keeps running with the reduced airflow and, if it was on high stage, steps down to low stage to try to recover. It stops if airflow drops to 0 CFM. The manual's probable causes are blocked or clogged filters, blocked or restrictive ductwork, and undersized ductwork.
Before you touch anything: the six signs that mean stop troubleshooting and call a pro →
Homeowner checks for Amana furnace code b9
These are limited airflow checks, not a complete furnace repair. If you smell gas or a carbon monoxide alarm sounds, leave the home right away without operating any switches, then call the gas utility or 911 from outside. Never bypass a safety switch or reset the furnace over and over.
- Turn the furnace off
Set the thermostat to off, then turn off the furnace's power switch near the unit. Do not open the electrical panel or any furnace compartment beyond the filter slot.
- Replace the filter with the same size and type
Slide out the accessible filter and check the size printed on its frame. Fit a replacement of the same size and type, following the airflow direction marked on the filter slot or in your unit's instructions. Keep the furnace off until the filter is in place.
- Open and clear room vents
Walk through the home and make sure every supply register and return grille is open and not blocked by furniture, rugs, or curtains. Do not reach into the ducts.
- Restore power and stop if the code returns
Turn the power switch back on and set the thermostat to call for heat once. If the same code comes back, leave the furnace off and call a licensed HVAC technician instead of resetting it again.
Ductwork evaluation, including whether the ducts are sized for the system, if b9 keeps coming back. DIY part cost: $5–25 — a pro visit for this class of fault typically runs $150–350.
What causes it (in order of likelihood)
- Blocked or clogged filter DIY-CHECKABLE
- Closed or blocked registers DIY-CHECKABLE
- Blocked, restrictive or undersized ductwork TECH
Parts referenced by this code
Always match parts against your model's parts list — part numbers vary within a series.
Questions about this code
What does b9 mean on an Amana furnace?
Indoor airflow fell below the minimum the control calculates from its shared data. The furnace keeps running with the reduced airflow and, if it was on high stage, steps down to low stage to try to recover. It stops if airflow drops to 0 CFM. The manual's probable causes are blocked or clogged filters, blocked or restrictive ductwork, and undersized ductwork.
How do I fix Amana furnace code b9?
With the power off, replace an accessible filter with the same size and type, then make sure every register is open. If b9 comes back, a technician should check the ductwork.
How much does it cost to fix Amana furnace code b9?
A clogged filter or closed registers may be the whole fix. If b9 keeps returning, cost depends on what a duct evaluation finds.
Applies to
AMVC96 · ACVC96
Different Amana generations use different code maps. If your series isn't listed, don't assume this meaning — check your blower-door label.
Same control platform, same code: Goodman furnace code b9
Full code lists for the other brands on this control platform: Goodman furnace codes
Verified against Goodman GMVC96/GCVC96 Service Manual, p.46 — “This condition occurs if the indoor airflow falls below a calculated minimum value.”
Verified against Goodman GMVC96/GCVC96 Service Manual, p.51-52 — “b9 LOW INDOOR AIRFLOW”
Verified against Goodman Diagnostic Code Identification System (GMVC96, GCVC96, AMVC96, ACVC96; code b9) — “Low Indoor Airflow”
Amana AMVC96/ACVC96 furnaces use the same control board and code map as the Goodman GMVC96/GCVC96 — the cited Goodman service manual is the platform document for both brands.
Last verified 2026-10-19 · page updated 2026-10-20 · how we verify
Related Amana furnace codes
These codes use the same dual 7-segment display (two-stage variable-speed) system.